Determination of Discrete-Structure Parameters of Coatings with Allowance for Residual Stresses

The authors suggest that the dimensions of a discrete section of a coating should be chosen on the basis of calculation of the critical crack spacing in cohesion cracking. This approach allows for residual stresses in the coating. The reliability of the calculation method has been verified experimentally by direct measurement of the crack spacing.     

Satellite SAR Remote Sensing of Great Lakes Ice Cover,Part 2. Ice Classification and Mapping

During the 1997 winter season, shipborne polarimetric backscatter measurements of Great Lakes (freshwater) ice types using the Jet Propulsion Laboratory C-band scatterometer, together with surface-based ice physical characterization measurements and environmental parameters, were acquired concurrently with Earth Resource Satellite 2 (ERS-2) and RADARSAT Synthetic Aperture Radar (SAR) data. This polarimetric data set, composed of over 20 variations of different ice types measured at incident angles from 0° to 60° for all polarizations, was processed to radar cross-section to establish a library of signatures (look-up table) for different ice types. The library is used in the computer classification of calibrated satellite SAR data. Computer analysis of ERS-2 and RADARSAT ScanSAR images of Great Lakes ice cover using a supervised classification technique indicates that different ice types in the ice cover can be identified and mapped, and that wind speed and direction can have an influence on the classification of water as ice based on single frequency, single polarization data. Once satellite SAR data are classified into ice types, the ice map provides important and necessary input for environmental protection and management, ice control and ice breaking operations, and ice forecasting and modeling efforts.     

长输管道不停输防腐层大修技术

东河塘至轮南输油管道,经过12年的运行,钢管外石油沥青玻璃布防腐层已严重老化甚至剥离。在不停输的情况下,对输油管道防腐层大修,特别像东—轮线输油管道,地处沙漠边缘、戈壁地带,没有成熟的施工经验可以借鉴。文章根据东—轮线输油管道防腐层大修的施工实践,详细介绍了长输管道不停输防腐层大修的施工工艺和质量保证措施。     

薄膜包衣技术及应用

对薄膜包衣技术及其在制剂生产中应用的研究进展作一综述。     

Synthesis and Evaluation of Blends Formed by Polymeric Crown Ethers and a Fullerene-Containing Primary Ammonium Salt in Organic Thin Films

The synthesis of a series of polymers and cyclopolymers bearing crown ethers of differing structure and affinities towards primary ammonium ions is discussed. These polymers have been tested in their efficiency to form structurally homogeneous thin films when blended with an amphiphilic C₆₀ compound containing a primary ammonium ion functional group. The X-ray reflectivity characterization of the films revealed that the polymer bearing the crown ether with the least affinity for primary ammonium ions, but having the highest degree of polymerization, is the most effective in forming structurally homogeneous thin films.     

Thermal Conductivity Measurement of an Electron-Beam Physical-Vapor-Deposition Coating

An industrial ceramic thermal-barrier coating designated PWA 266, processed by electron-beam physical-vapor deposition, was measured using a steady-state thermal conductivity technique. The thermal conductivity of the mass fraction 7 % yttria-stabilized zirconia coating was measured from 100 °C to 900 °C. Measurements on three thicknesses of coatings, 170 μm, 350 μm, and 510 μm resulted in thermal conductivity in the range from 1.5 W/(m·K) to 1.7 W/(m·K) with a combined relative standard uncertainty of 20 %. The thermal conductivity is not significantly dependent on temperature.     

平面波谱法分析电磁波在管道中的传播

通过分析电磁波从管道开口耦合进入管道的绕射机理及场在腔体内的射线特征，将进入管道的绕射场展开为平面波谱，利用平面波在自由空间的传播特性分析了电磁波沿管道的传输和反射特征。通过算例验证了该算法的有效性。     

Ideally selective diisocyanate building blocks: New perspectives for dendrimers and coating binders

Using zirconium (IV) salts as catalyst, the reaction of a diisocyanate carrying one tertiary and one primary isocyanate group (IMCI, DIMP) with alcohols can be conducted with complete regioselectivity. This unique selectivity enables the use of a diisocyanate building block in unprecedented ways. Incomplete regioselectivity of diisocyanates, as commonly encountered in currently commercial ones like IPDI and TDI, inevitably leads to polydisperse products in reaction with polyols. The ultimate monodisperse polymer architecture, dendrimers, can now be made in a facile, straightforward manner using IMCI as the ideal diisocyanate building block. Coating applications of this unique building block are not restricted to these perfect branching polymers, but also include isocyanate-functional coating resins. Without any increase in polydispersity, a hydroxyl-functional polyester can be end-capped with the IMCI diisocyanate and subsequently serve as a crosslinker in powder coatings.     

In situ polymerization and characterization of polyester‐based polyurethane/nano‐silica composites

Polyester‐based polyurethane/nano‐silica composites were obtained via in situ polymerization and investigated by Fourier‐transform infrared spectroscopy (FTIR), or FTIR coupled with attenuated total reflectance (FTIR‐ATR), Transmission electron microscopy (TEM), atomic force microscopy (AFM), an Instron testing machine, dynamic mechanical analysis (DMA) and ultraviolet‐visible spectrophotometry (UV‐vis). FTIR analysis showed that in situ polymerization provoked some chemical reactions between polyester molecules and nano‐silica particles. FTIR‐ATR, TEM and AFM analyses showed that both surface and interface contained nano‐silica particles. Instron testing and DMA data showed that introducing nano‐silica particles into polyurethane enhanced the hardness, glass temperature and adhesion strength of polyurethane to the substrate, but also increased the resin viscosity. UV‐vis spectrophotometry showed that nano‐silica obtained by the fumed method did not shield UV radiation in polyurethane films. Copyright © 2003 Society of Chemical Industry